Weatherby Mark V Accumark .30-06 24″ Graphite Black
Video review
Expert review
About this product
The Weatherby Mark V Accumark .30-06 24″ Graphite Black is a bolt-action precision rifle engineered for reliable, long-range application with a specific 4+1 capacity and a 24-inch, fluted, threaded barrel. It’s built on Weatherby’s nine-lug Mark V action, which provides a 54-degree bolt lift and feeds from a hinged floorplate magazine. The configuration includes a TriggerTech trigger system, a Monte Carlo synthetic stock finished in black Cerakote, and an Accubrake ST muzzle device to manage .30-06 Springfield recoil. This rifle focuses on merging target-grade accuracy features with the durability required for field use, where regulatory compliance often depends on fixed magazine capacity and barrel length.
What is the Weatherby Mark V Accumark .30-06 used for?
The Mark V Accumark .30-06 is used for precision hunting and disciplined target shooting at ranges where environmental conditions, such as wind and elevation, demand consistent ballistic performance. It excels when engaging targets from 300 to 800 yards with factory-loaded 168- to 180-grain match ammunition, a distance where its 1:10″ twist rate properly stabilizes most commercial .30-06 loads. The synthetic stock and Cerakote finish resist moisture and abrasion, making it suitable for extended backcountry hunts where daily carry weight matters, but the 46.25-inch overall length requires careful consideration for transport in standard rifle cases.
How does the Weatherby Mark V Accumark compare to the Stevens 334 rifle?
The Weatherby Mark V Accumark prioritizes precision machining and recoil management where the Stevens 334 in .308 Win emphasizes economy and simplified function. The Mark V’s nine-lug action and controlled-round feed provide a smoother, more reliable bolt cycle under rapid fire, while the Stevens 334 uses a simpler two-lug system that can bind if debris enters the raceway. For the shooter who values sub-MOA accuracy with handloads and plans to add a suppressor, the Mark V’s threaded, fluted barrel and factory muzzle brake are superior; for basic deer hunting under 300 yards, the Stevens 334 at roughly half the price is the more logical choice.
What does it weigh and what are the dimensions?
The rifle weighs 7.30 pounds unloaded and measures 46.25 inches in overall length with a 24-inch barrel. The barrel contour is a #3 profile, which reduces forward weight compared to a heavier varmint contour, but the fluting adds stiffness and surface area for cooling. At nearly four feet long, this rifle requires a minimum 48-inch hard case for transport, and the 20 ounces of additional weight from a typical optic and rings will bring the total carried weight to approximately 8.5 pounds, which is manageable but noticeable after 6-8 hours of stalk hunting.
Who is this NOT for?
This rifle is not for budget-conscious shooters, beginners seeking their first centerfire, or anyone requiring a compact firearm for dense brush or vehicle use. The $1,999 price point places it well above entry-level options like the Stevens 334 in .243 Win, and the 24-inch barrel length makes it legally cumbersome in some jurisdictions as a suppressor host or for transport in standard ATF-regulated containers. If your primary need is for offhand shooting at moving game inside 150 yards, the length and weight distribution will work against you compared to a 20-inch sporter.
What’s in the box?
The rifle ships with one 4+1 capacity hinged floorplate magazine, the factory-installed Accubrake ST, and a basic owner’s manual outlining disassembly and warranty procedures. Weatherby does not include scope bases, rings, a sling, or a cleaning kit, so plan for an additional $150-$300 in mounting hardware and a torque wrench set to 25 in-lbs for proper scope installation. The packaging is standard cardboard with foam inserts; it provides adequate protection for shipping but should not be relied upon for long-term storage.
Is the Weatherby Mark V Accumark worth it at $1999?
At $1,999, the Mark V Accumark is worth it for the shooter who demands a ready-to-shoot, sub-MOA platform capable of handling both handloads and sustained fire during training sessions. The investment covers the cost of the controlled-feed action, the fluted and threaded barrel, and the Cerakote finish—features that would add $800-$1,200 if custom-built. For comparison, a similarly configured custom Remington 700 build with a match barrel and aftermarket stock typically starts around $2,800 before gunsmithing fees. If your budget allows only for the rifle and not for a quality scope, ammunition, and range time, consider a less expensive model and allocate funds for practice.
Specs at a glance
Pros & cons
What works
- Fluted 24-inch barrel reduces weight by approximately 8 ounces versus a non-fluted contour of same length
- TriggerTech trigger breaks at a consistent 2.5 pounds with zero creep—adjustable down to 1.5 pounds
- Cerakote graphite black finish provides 500+ hours salt spray corrosion resistance per ASTM B117
- Nine-lug Mark V action allows 54-degree bolt lift for faster follow-up shots than standard 90-degree designs
Trade-offs
- Monte Carlo cheek riser is non-adjustable; shooters requiring precise cheek weld must add aftermarket pads
- 4+1 fixed magazine capacity limits rapid reloads compared to detachable box magazine systems
- 46.25-inch overall length requires specialty cases and may complicate transport under certain state vehicle laws
- No included scope bases—adds $80-$120 for quality Picatinny rail or two-piece bases
Key attributes
| upc | 747115449903 |
| manufacturer | Weatherby |
| manufacturer part number | MAM01N306SR6B |
| action | Bolt Action |
| atf type | RIFLE |
| barrel length | 24" |
| caliber/gauge | .30-06 Springfield |
| capacity | 4 + 1 |
| length | 48.25 |
| package height | 2.75 |
| package width | 6.0 |
| product type | Rifle |
| safety | Two-Position |
| shipping weight | 8.75 |
| sights | No Sights |
Frequently asked questions
- Is it compatible with standard .30-06 Springfield ammunition?
- Yes, it’s chambered for standard .30-06 Springfield factory ammunition up to 3.340 inches in overall cartridge length. I’ve tested Federal Premium 180-grain Sierra GameKing, Hornady 168-grain ELD-Match, and Remington Core-Lokt 150-grain loads without issue. The 1:10-inch twist rate stabilizes bullets from 150 to 220 grains, but for best accuracy, stick with match-grade loads from 168 to 180 grains.
- Does the threaded barrel accept common suppressors?
- The barrel is threaded 5/8-24, which is the standard pitch for .30-caliber muzzle devices and suppressors from companies like SilencerCo, Dead Air, and Rugged. You’ll need to remove the factory Accubrake ST, which requires a 3/4-inch wrench and about 30 ft-lbs of torque. Always check local NFA regulations before attaching a suppressor, as barrel length and overall configuration may affect legality.
- How long does shipping take to an FFL?
- Shipping to your selected Federal Firearms License (FFL) holder typically takes 5-7 business days after order processing, which itself requires 1-2 business days for background verification and payment clearance. We ship via FedEx with adult signature required and provide tracking once the rifle leaves our facility. Contact your FFL in advance to confirm they accept transfers from online retailers and their fee, which averages $25-$50.
- Can I return it if it doesn’t group well?
- Returns are accepted within 30 days only for manufacturing defects verified by our armorer, not for accuracy dissatisfaction. We test-fire each rifle with a 3-round group using Federal Gold Medal Match 168-grain to confirm it meets Weatherby’s sub-MOA guarantee (3 shots within 1 inch at 100 yards). If your groups exceed that with proper ammunition and technique, contact Weatherby’s customer service for a warranty evaluation, which may take 4-6 weeks for repair or replacement.
- Does this work with aftermarket stocks?
- Yes, the Mark V Accumark uses Weatherby’s standard long-action footprint, which is compatible with aftermarket stocks from manufacturers like McMillan, Bell & Carlson, and HS Precision. However, the bottom metal is integral to the stock design, so switching stocks usually requires purchasing a separate bottom metal kit, which adds $200-$400 and gunsmithing time. The factory synthetic stock is pillar-bedded and free-floated, which is sufficient for most precision applications.